RESUMO
Microscale abrasion has been intensively used to study the wear behavior o several hard coatings, enabling the observation of different wear mechanisms. Recently, a study arguing whether the surface texture of the ball could influence the dynamics of abrasive particles throughout the contact was presented. In this work, the influence of the abrasive particles concentration able to change the texture of the ball was studied to understand its influence on the wear modes-rolling or grooving. Thus, tests were carried out using samples with a thin coating of TiN, deposited using the Physical Vapor Deposition (PVD) technique, and AISI 52100 steel balls etched over 60 s to induce a change in their texture and roughness were used. Three abrasive slurries were prepared with black silicon carbide (SiC) particles (average particle size of 4 µm) with different concentrations, 0.25, 0.35, and 0.45 g/cm3. The rotation speed used in the tests was 80 rpm and the normal loads applied in the study were 0.2 N and 0.5 N, and 1 N. After the wear tests, the coated samples and tracks on the surface of the balls were observed by SEM and 3D microscopy to understand the abrasive particle dynamics, evaluating the wear mode transition as well as the function of both applied load and slurry concentration. The tracks in the balls showed particles embedded on their surface. A lower concentration of abrasion was conducted to higher specific wear rate. Moreover, a predominant two-body wear mechanism was induced when the abrasive concentration was increased. There was an increase in the roughness of the scar and the surface of the balls with an increase in the abrasive particles' concentration.
RESUMO
Duplex stainless steels are being used on applications that require high corrosion resistance and excellent mechanical properties, such as the naval and oil-gas exploration industry. The components employed in these industries are usually obtained by machining; however, these alloys have low machinability when compared to conventional stainless steels, usually requiring the employment of tool coatings. In the present work, a comparative study of TiAlSiN coating performance obtained by these two techniques in the milling of duplex stainless-steel alloy LDX 2101 was carried out. These coatings were obtained by the conventional direct current magnetron sputtering (dc MS) and the novel high power impulse magnetron sputtering (HiPIMS). The coatings were analyzed and characterized, determining mechanical properties for both coatings, registering slightly higher mechanical properties for the HiPIMS-obtained coating. Machining tests were performed with varying cutting length and feed-rate, while maintaining constant values for axial and radial depth of cut and cutting speed. The surface roughness of the material after machining was assessed, as well as the wear sustained by each of the tool types, identifying the wear mechanisms and behavior of these tools, as well as registering the flank wear values presented for each of the tested tools. The HiPIMS-obtained coating exhibited a very similar behavior when compared to the other, producing similar surface roughness quality. However, the HiPIMS coating exhibited less wear for higher cutting lengths, proving to be a better choice in this case, especially regarding tool life.
RESUMO
Micro-abrasion remains a test configuration hugely used, mainly for thin coatings. Several studies have been carried out investigating the parameters around this configuration. Recently, a new study was launched studying the behavior of different ball materials in abrasive particles' dynamics in the contact area. This study intends to extend that study, investigating new ball materials never used so far in this test configuration. Thus, commercial balls of American Iron and Steel Institute (AISI) 52100 steel, Stainless Steel (SS) (AISI) 304 steel and Polytetrafluoroethylene (PTFE) were used under different test conditions and abrasive particles, using always the same coating for reference. Craters generated on the coated samples' surface and tracks on the balls' surface were carefully observed by Scanning Electron Microscopy (SEM) and 3D microscopy in order to understand the abrasive particles' dynamics. As a softer material, more abrasive particles were entrapped on the PTFE ball's surface, generating grooving wear on the samples. SS AISI 304 balls, being softer than the abrasive particles (diamond), also allowed particle entrapment, originating from grooving wear. AISI 52100 steel balls presented particle dynamics that are already known. Thus, this study extends the knowledge already existing, allowing to better select the ball material to be used in ball-cratering tests.
